Cobra 3195 Alarm Manual Full -
The 3195 features a dual-zone impact sensor.
If the sensor is too sensitive (triggers by wind or passing trucks) or not sensitive enough, the adjustment knob is usually located on the main alarm module (the black box installed under the dash) or on a small module wired to it. Rotate the knob slightly clockwise (more sensitive) or counter-clockwise (less sensitive).
Here's how to use the Cobra 3195 alarm system:
Troubleshooting and Maintenance
If you encounter any issues with your Cobra 3195 alarm system, refer to the troubleshooting section in the manual. Here are some common problems and solutions:
Conclusion: The Cobra 3195 alarm manual provides comprehensive instructions and features for the Cobra 3195 alarm system. By following this guide, you'll be able to install, program, and operate your alarm system with ease. Remember to refer to the manual for specific instructions and troubleshooting tips.
Download the Full Cobra 3195 Alarm Manual: You can download the full Cobra 3195 alarm manual in PDF format from the manufacturer's website or other online sources.
The Cobra 3195 is part of the legacy 3000 series (similar to the 3193 and 3198 models), which are standard vehicle security systems featuring radio remote control, engine immobilization, and volumetric protection. Core Operation Guide
Arming: Press the large button (A) on the remote key fob. The direction lights will flash twice to confirm the system is armed.
Disarming: Press the small button (B). The direction lights will flash once, and the status LED will turn off.
Emergency Override: If the remote fails, you must use the unique 4-digit PIN code provided on the system's security card. Programming New Remote Fobs
To add a new transmitter (up to 4 per system), follow these sequential steps:
Prepare Remotes: Press both buttons on the remote simultaneously until the LED stops flashing (approx. 10 seconds). The LED will then stay illuminated. Repeat for all remotes you intend to use.
Initialize Mode: Turn the ignition ON and OFF 3 times within 7 seconds. The dashboard security LED will light for 3 seconds. Enter PIN: Immediately after the LED goes out, turn the ignition ON.
Count the LED flashes until they reach your first PIN digit, then turn the ignition OFF.
Turn ignition ON again and repeat for the remaining three digits.
Sync: If the code is correct, the LED remains lit. Press the large button on each remote until the dashboard LED goes out and comes back on to confirm sync. Exit: Turn the ignition OFF and test each fob. Common Troubleshooting
Battery Low: If the remote's LED flashes weakly or the system beeps upon disarming, replace the remote battery.
Trigger History: If the alarm went off while you were away, the status LED will blink in a specific pattern when you disarm: 1 blink: Door or boot opened. 3 blinks: Bonnet opened. 4 blinks: Ignition/hotwire attempt. 5 blinks: Volumetric/motion sensor triggered. Coding new Cobra remote. - Technical Talk
The Cobra 3195 is a legacy vehicle security system often installed in cars like the Lotus Elise and Exige. Since this model is part of Cobra's older "Bridge" or "8000" series, it shares core operational procedures with models like the 3198 and 8185. 1. System Operation on the remote key fob. Indicators:
Turn indicators blink twice; the status LED begins to flash. Disarming: Indicators: Turn indicators blink once; the status LED goes out. Ultrasonic Sensor Exclusion: If you need to leave a pet or person inside, press
within 20 seconds of arming to disable interior motion sensors for that cycle. Midlands Lotus Owners Club 2. Emergency PIN Override
If your remote is lost or the battery is dead, you can disarm the system using your unique 4-digit PIN: Midlands Lotus Owners Club Turn the ignition ON and OFF 3 times within 5 seconds.
The security LED will blink once to signal it is ready for the PIN. Enter the 1st digit: Turn the ignition
, count the number of LED blinks equal to the first digit, then turn the ignition Repeat Step 3 for the remaining three digits. If correct, the alarm will disarm. Midlands Lotus Owners Club 3. Remote Key Fob Programming To sync a new or existing remote: Midlands Lotus Owners Club Prepare remotes:
Hold both buttons on the remote until the fob LED stops flashing (approx. 10 seconds). The LED will then stay lit. Enter Program Mode: Perform the ignition ON/OFF 3 times sequence (same as PIN entry) and enter your 4-digit PIN. Once the PIN is accepted and the ignition is , the security LED will stay lit. Press the large
on each remote. The security LED will blink once to confirm each one. Turn off the ignition to exit. Midlands Lotus Owners Club 4. Troubleshooting LED Flash Codes
After an alarm trigger, the dashboard LED will flash a specific pattern to indicate the cause:
How to Read Vodafone Automotive & Cobra Car Alarm Fault Codes
While official printed manuals for legacy products like the Cobra 3195 cobra 3195 alarm manual full
are no longer produced, digital versions and comprehensive guides are available through the Cobra Support Portal Cobra 3195
is part of the 3100 series (often grouped with models like the 3198), sharing core functionality for vehicle security.
Below is a breakdown of the essential operational and technical information found in the full manual. 🛡️ Core Security Features
Perimeter Protection: Monitors door, boot, and bonnet triggers.
Volumetric Protection: Uses ultrasonic sensors to detect movement inside the cabin.
Immobilization: A dual-circuit immobilizer prevents the engine from starting without authorization.
Panic Function: Allows the user to trigger the siren manually via the remote. 🔌 Operational Basics
Arming: Press the main button on the remote; indicators flash twice.
Disarming: Press the secondary button; indicators flash once.
Emergency Override: If the remote fails, you can use a 4-digit PIN code or a touch key to disarm the system manually. 🛠️ Programming & Troubleshooting Diagnostic Flash Codes
If the alarm is triggered, the dashboard LED will flash in a specific sequence to identify the source of the breach: 3 Flashes: Ultrasonic sensor trigger. 4 Flashes: Attempted hotwire/ignition trigger. 5 Flashes: Boot or bonnet circuit issue. Remote Programming To sync a new key fob, you typically follow these steps:
Disarm the system and turn the ignition ON/OFF 3 times within 7 seconds. The LED will flash to signal programming mode.
Press and hold buttons on the new fob for 10 seconds until the system confirms with a flash or beep.
💡 Pro Tip: For legacy models, it is highly recommended to view manuals on a desktop computer, as the PDF formatting may not display correctly on mobile devices. Download Product Manuals for your Cobra Device
Search for "Cobra 3195 alarm manual PDF" or "Cobra 3195 installation manual" to download the exact wiring diagram, full programming codes, and safety details for your unit.
Cobra 3195 is a comprehensive vehicle security system featuring ultrasonic sensors, engine immobilization, and a high-power battery backup siren. This report compiles key operational procedures and technical details derived from its standard manual. System Operations Arming & Disarming
: The system integrates with your vehicle's original remote keys. Locking the doors automatically arms the system (indicated by a long flash of the indicators); unlocking disarms it. Volumetric Sensor Exclusion
: If you leave people or pets inside the vehicle, you can temporarily disable the ultrasonic sensors. Turn the ignition off, press the LED button on the dashboard within 5 seconds, and then arm the system as usual. Emergency Disarming
: If your remote fails, you can disarm the system using a unique 4-digit
. This is done by turning the ignition ON and counting the flashes of the LED to enter each digit. Alarm Trigger Memory
If the alarm was triggered while you were away, the LED will flash in a specific sequence when you disarm the system and turn on the ignition. To identify the cause, count the number of flashes: : Door, boot, or bonnet opened. : Ultrasonic sensors triggered (movement inside). : Ignition attempt detected. : Tampering with power supply or siren. Technical Specifications Specification
High-power, battery-backed (functions even if vehicle battery is cut). Protection Perimeter (doors/hood) and Volumetric (interior space). Passive arming and "auto-locking" features (programmable). Integration Supports CAN-bus and PLIP (remote key) interfaces. Troubleshooting & Support Fault Identification
: If the system emits several beeps after disarming, it is signaling a previous alarm activation. Consult the flash codes above to identify the fault. Manual Access : For the full PDF manual, you can search the Cobra Product Support site which hosts legacy product documentation. LED Indicators
: A steady LED indicates the system is in "pre-arm" mode (approx. 20-30 seconds after locking). Once it begins to flash slowly, the system is fully armed. www.cobra.com for emergency disarming? Product Help/Manuals
Complete User Guide for the Cobra 3195 Alarm System The Cobra 3195 is a modular car security system designed to provide comprehensive protection, including perimetric monitoring and ultrasonic interior detection. This guide synthesizes essential operations, programming steps, and troubleshooting tips from official documentation and technical support resources. Core Remote Functions
The system is typically operated via a two-button radio control.
Button A (Large): Arms and disarms the system. Pressing it once locks the doors and activates sensors; pressing it again unlocks the doors and disarms the alarm. Button B (Small): Used for secondary features.
Panic Alarm: Press and hold Button B to trigger the siren manually in an emergency.
Sensor Exclusion: To leave a pet or person inside, press Button B within 20 seconds of arming to temporarily disable the internal ultrasonic sensors. Emergency PIN Override The 3195 features a dual-zone impact sensor
If your remote fails or is lost, you can disarm the system using your unique 4-digit PIN code: Cobra 8185 Alarm System Manual | PDF - Scribd
USER INSTRUCTIONS USER INSTRUCTIONS * Car Alarm Immobiliser System. Thatcham M.I.R.R.C. Evaluation No: ... * Radio Key Function. *
Coding new Cobra remote. - Midlands Lotus Owners Club (MLOC)
Cobra 3195 Alarm Manual Full: A Comprehensive Guide to Securing Your Vehicle
Are you a proud owner of a Cobra 3195 alarm system for your vehicle? Congratulations on taking the first step towards ensuring the safety and security of your prized possession. With a Cobra 3195 alarm system, you can rest assured that your vehicle is protected against theft and vandalism. However, to get the most out of your alarm system, it's essential to have a thorough understanding of its features, installation, and operation.
In this article, we'll provide you with a comprehensive guide to the Cobra 3195 alarm manual full, covering everything from installation to troubleshooting. Whether you're a new owner or have been using the system for a while, this article aims to provide you with a deeper understanding of your Cobra 3195 alarm system.
Overview of the Cobra 3195 Alarm System
The Cobra 3195 is a state-of-the-art alarm system designed to provide maximum protection for your vehicle. With its advanced features and user-friendly interface, it's no wonder that it's a popular choice among vehicle owners. Here are some of the key features of the Cobra 3195 alarm system:
Installation of the Cobra 3195 Alarm System
Installing the Cobra 3195 alarm system requires some technical expertise, but with the right guidance, you can do it yourself. Here are the general steps to follow:
Operation of the Cobra 3195 Alarm System
Once you've installed the Cobra 3195 alarm system, it's essential to understand how to operate it effectively. Here are some general guidelines:
Troubleshooting the Cobra 3195 Alarm System
Like any electronic system, the Cobra 3195 alarm system may occasionally experience issues. Here are some common problems and their solutions:
Cobra 3195 Alarm Manual Full: Tips and Tricks
Here are some additional tips and tricks to help you get the most out of your Cobra 3195 alarm system:
Conclusion
The Cobra 3195 alarm system is a powerful tool for securing your vehicle. With its advanced features and user-friendly interface, it's an excellent choice for vehicle owners who want to protect their prized possession. By following the guidelines outlined in this article, you can ensure that your Cobra 3195 alarm system is installed, operated, and maintained correctly.
Remember to consult the Cobra 3195 alarm manual full for detailed instructions and technical specifications. With the right guidance and support, you can enjoy peace of mind knowing that your vehicle is protected by a state-of-the-art alarm system.
FAQs
Downloads
Additional Resources
The Cobra 3195 is a Thatcham approved category 1 alarm and immobiliser system. It typically consists of:
| Button | Function | Typical Use | |--------|----------|-------------| | MENU | Access configuration screens | Changing settings, adding users, etc. | | ▲ / ▼ | Navigate up‑down or increase/decrease values | Adjusting numbers, scrolling menus | | ENTER | Confirm selection | Saving changes, arming/disarming | | ARM | Initiate arming sequence | Quick arm (default mode) | | TEST | Run a sensor test | Verify each zone works | | SILENCE | Mute audible alarm | When a false alarm occurs | | LED indicators | | Quick visual status at a glance |
Disclaimer: This guide serves as a reference based on standard Cobra 3195 configurations. Vehicle-specific wiring and features may vary based on the installation date and the specific vehicle manufacturer's integration.
The manual for the Cobra 3195 alarm (part of the 3100 series from Vodafone Automotive) details procedures for arming, disarming, and emergency overrides. This system is a Thatcham-approved modular alarm typically controlled by the vehicle's original remote or a Cobra-specific key fob. Core Operations Arming/Disarming
: Generally synchronized with your vehicle’s central locking. If using a Cobra remote, press the large button to arm (confirmed by two beeps and flashes) and the same button to disarm (one beep and flash). Emergency Override
: If your remote fails, you can disarm the system using a unique Personal Identification Number (PIN) found on the "Cobra PIN Card" provided at installation. Turn the ignition
3 times within 7 seconds. The status LED will illuminate for 3 seconds. Immediately after the LED goes out, turn the ignition If the sensor is too sensitive (triggers by
Count the LED flashes for the first digit of your PIN. Turn the ignition once the count is reached, then back Repeat for the remaining three digits. Key Functions & Indicators LED Status Rapid Flashing
: The system is in the "pre-arm" phase (approx. 20–30 seconds). Slow Flashing : System is fully armed. Diagnostic Flashes
: If the alarm triggered while you were away, the LED will flash in a specific sequence (e.g., 5 flashes for a boot/bonnet circuit issue) when you disarm it. Volumetric Protection
: To arm the alarm while leaving a pet or person inside (disabling internal motion sensors), press the remote button twice within 3 seconds when arming. Programming & Manuals New Remotes
: Programming usually requires entering the PIN first to put the system into "learning mode." Once in mode, you press both buttons on the remote for 10 seconds until the remote's LED stops flashing and stays on. Digital Copies
: You can find full PDF documentation for similar 3100-series models (like the 3198) on or the official Vodafone Automotive Manuals Portal Do you need the specific wiring diagram for installation or the programming code sequence for a new key fob?
In this section you will find our manuals - Vodafone Automotive
Cobra 3195 is a modular alarm system typically controlled via the vehicle's original remote. While a single "full text" digital manual is rarely hosted as a plain text file, the system's operation and installation are covered by these key technical specifications and procedures: System Overview The 3195 is a CAN-bus or PLIP
(Passive Luxury Information Protocol) interface alarm. It integrates with your car's existing central locking system to arm and disarm when you lock or unlock the doors. Standard Operation
: Press the "Lock" button on your vehicle's original remote. The hazard lights will flash once, and the LED will begin to flash.
: Press the "Unlock" button on your vehicle's original remote. The hazard lights will flash twice, and the LED will stop flashing. Passive Arming
: If programmed, the system may arm itself automatically 30 seconds after the ignition is turned off and the last door is closed. Emergency Disarming (PIN Code)
If your remote fails, you can disarm the alarm using a 4-digit PIN code (found on the "Touch Panel" or your installation card):
Open the door with the mechanical key (the alarm will sound). Switch the ignition
The LED will flash. Count the number of flashes corresponding to the first digit of your PIN. Switch the ignition and then back
Repeat for the remaining three digits. The alarm will disarm after the fourth digit is entered correctly. LED Diagnostic Signals
The LED on the dashboard communicates the cause of the last alarm trigger: : Door, boot, or bonnet opening. : Ultrasonic sensors (interior movement). : Ignition attempt. : Tamper/Power cut. Installation & Programming Highlights Ultrasonic Sensitivity
: Usually adjusted via a trimmer on the siren/control unit or via specialized programming tools. Hazard Light Connection
: Connected to the vehicle's indicators to provide visual confirmation.
: The system typically uses a battery-backed wireless or wired siren (e.g., Cobra 5100 series).
DRAFT REPORT: COBRA 3195 ALARM MANUAL FULL
Introduction
The Cobra 3195 is a state-of-the-art alarm system designed to provide users with a reliable and efficient way to secure their properties. This report aims to provide a comprehensive guide to the Cobra 3195 alarm manual, covering its features, installation, operation, and troubleshooting.
System Overview
The Cobra 3195 alarm system is a wireless, microprocessor-based security system that offers a range of features, including:
Components and Accessories
The Cobra 3195 alarm system consists of the following components:
Installation
Fix: Lower the shock sensor sensitivity (see 3.3). Also check the door pin switches – if any are corroded, the 3195 sees a door open. Clean or replace pin switches.
| Step | Action | Details | |------|--------|---------| | 1 | Power the Unit | Connect the power adapter (12 V DC, 1 A) to the rear power jack. The unit will power up within a few seconds and the LCD will show “‑‑‑”. | | 2 | Set the Date & Time | Press MENU → SETUP → TIME/DATE. Use the ▲/▼ keys to adjust, ENTER to confirm. | | 3 | Select the Alarm Mode | Press MODE until you see OFF / HOME / AWAY on the display. Each mode has a different sensor sensitivity (see “Alarm Modes” below). | | 4 | Arm the System | Press ARM. The LCD will flash “ARMING” for 30 s (you can adjust the delay in the menu). After the countdown the display shows the selected mode (HOME or AWAY). | | 5 | Disarm | Enter your 4‑digit PIN on the keypad and press ENTER. The system returns to OFF. | | 6 | Test Sensors | From the main screen press TEST → choose a zone → ENTER. The sensor will beep and the LCD will indicate “OK” or “FAIL”. |