Garmincure3exe Full May 2026

In dealing with executable files like GarminCure3.exe, caution and verification are key. Always prioritize files from trusted sources and perform necessary safety checks before execution. If in doubt, consider reaching out to the software developer or a tech professional for guidance.

For those deep in the world of GPS modification, GarminCure3.exe

is a legendary "life-saver" tool designed to unbrick devices stuck in endless boot loops. It essentially acts as a surgical instrument for Garmin firmware, allowing users to strip away the corrupted "fat" of a standard update and replace it with a "Cure" version that forces the device into Mass Storage mode. How the "Cure" Works When a Garmin device (like a classic

) becomes a "brick"—meaning it won't fully boot or connect to a PC—it’s often because a file system error is preventing the OS from loading. The Patched Firmware

: GarminCure3 takes an original firmware file (GUPDATE.GCD) and patches it to bypass the standard boot process. Mass Storage Access : Once the "Cure" firmware is flashed using Updater.exe

, the device stops trying to boot and instead appears as a removable drive on your computer. The Final Fix

: Once you have drive access, you can delete the corrupted files or reformat the internal memory before flashing the firmware back to restore full functionality. Essential Tools for the Process

If you are attempting to revive a dead unit, you typically need this "recovery kit": GarminCure3.exe : The primary tool for creating patched firmware. Updater.exe

: The utility used to push that firmware to the device via USB.

: Often used alongside GarminCure3 to safely reformat the internal storage. Pre-Boot Mode

: A specific hardware key combination unique to each model (e.g., holding the top-left corner of the screen while powering on) that allows the PC to recognize the device before it crashes. Compatibility While primarily tested on the nüvi 200, 13xx, 14xx, and 37xx

series, it is widely considered compatible with most non-Linux, non-marine Garmin automotive units. However, it requires running as an Administrator

The GarminCure3.exe tool is a utility used to "unbrick" Garmin devices that are stuck in boot loops or cannot be recognized by a computer. It works by patching the original firmware to create a "CURE" version that forces the device into a state where its internal storage can be accessed and fixed. Prerequisites GarminCure3.zip: Contains GarminCure3.exe and updater.exe.

Original Firmware: A .GCD file for your specific device model from the Garmin website.

Drivers: Ensure Garmin USB drivers are installed on your PC. Step-by-Step Procedure 1. Prepare the Cure Firmware Run GarminCure3.exe.

Drag and drop your original .GCD firmware file into the "Input file" box. Select the CURE option (this is typically the default).

Click Make firmware. The program will process the file and notify you when it is finished. 2. Flash the Device in Pre-boot Mode

Click the Updater button within the GarminCure3 interface to launch updater.exe. In the Updater window, select USB Device. Put your device into Pre-boot Mode: Ensure the device is powered off.

Press and hold a specific screen area (often the top-left corner) or a specific button (like START/STOP) while connecting it to your PC via USB.

Once the device details appear in the Updater window, click OK immediately while still holding the screen/button. Release the button/screen once the progress bar begins. 3. Repair the Internal Storage

After flashing the CURE firmware, the PC should recognize the Garmin as a Removable Disk.

Identify and remove any corrupt files (e.g., recently added maps or GPX files) using Windows Explorer.

If the issue persists, you may need to use a tool like RMPrepUSB to format the drive. 4. Restore Original Firmware

Once the storage is cleaned or formatted, go back to GarminCure3.exe. Select the ORIGINAL option instead of "CURE". Click Make firmware and then Updater.

Repeat the flashing process (Step 2) to return the device to its factory software state. Troubleshooting Tips

Device Not Recognized: Try a different USB cable or port, or run updater.exe as an administrator.

Infinite Loops: If the device still won't boot after flashing the original firmware, ensure you have replaced necessary system folders (like the Garmin folder) if you performed a format.

Pre-boot Fail: Timing is critical; you must click "OK" on the Updater tool as soon as the device is detected. Garmin Fenix 6X Pro stuck in bootloop - fēnix 6 Series

Reviving Your Brick: A Guide to GarminCure3 Is your Garmin stuck in a permanent reboot loop or failing to load past the startup logo? When standard resets fail, many enthusiasts turn to GarminCure3.exe, a powerful utility designed to "unbrick" devices by forcing them into a state where they can be recognized by a computer again. What is GarminCure3?

GarminCure3 is a third-party tool used to create "cure" firmwares. It essentially patches official Garmin firmware so that the device skips its normal (and likely broken) boot sequence, instead activating a Mass Storage Mode connection. This allows you to access the internal memory to delete corrupted files—like a bad map image or a buggy .gcd file—that are preventing a successful start. The Recovery Process

To use the "full" recovery method, you generally need three things: the GarminCure3 tool, the Updater.exe utility, and the original firmware for your specific device model.

Prepare the Cure: Load your original firmware into GarminCure3, select the CURE option, and click "Make firmware" to generate the patched version.

Enter Pre-Boot Mode: This is the most critical step. For many models, like the Nüvi, you must hold the top-left corner of the screen while connecting the USB cable to your PC.

Flash the Device: Use Updater.exe to send the cure firmware to the device while it is in pre-boot mode.

Fix the Files: Once the cure is applied, your PC should recognize the Garmin as a removable drive. You can then delete the offending corrupted files or even reformat the drive using tools like RMPrepUSB if necessary.

Return to Original: After the device is cleaned, repeat the flashing process using the ORIGINAL firmware setting in GarminCure3 to restore normal operation. Important Safety Tips

Backup First: Always back up your GUPDATE.GCD and other vital files if you can gain even temporary access to the drive.

Check HWID: Ensure you are using the firmware that matches your device’s specific Hardware ID (HWID) to avoid further damage.

Battery Charge: Ensure your device has enough power before attempting to flash firmware to prevent a shutdown mid-process.

For official software updates and standard map management, it is always recommended to use the Garmin Express desktop app first before attempting advanced recovery tools. GarminCure3 tool - the new way to create cure firmwares for

GarminCure3.exe is a third-party firmware utility used to unbrick Garmin devices that are stuck in a boot loop or fail to be recognized by a computer. It works by patching original Garmin firmware to bypass the normal boot sequence, forcing the device into Mass Storage Mode so you can delete corrupted files or reformat the internal storage.  Core Functionality 

Cure Firmware Generation: Creates a "cure" version of original firmware that prevents the device from hanging on screens like "Loading maps...".

Enabling Mass Storage: Allows a "soft-bricked" device to appear as a drive on your PC, even if it is currently stuck on the logo screen.

Original Firmware Restoration: Once the corrupted files are removed, the tool can flash the original, unpatched firmware back onto the device to restore normal operation.  Typical Usage Steps 

Preparation: Download the original firmware (.GCD file) for your specific device model. garmincure3exe full

Generate Cure: Open GarminCure3.exe, load your GCD file, select the CURE radio button, and click Make firmware.

Flashing: Click the Updater.exe button within the interface. Set the connection type to USB Device.

Pre-boot Mode: Power off the device and put it into "Pre-boot mode" (often by holding a specific corner of the screen or button combination while connecting to USB) to allow Updater.exe to detect it.

Curing: Once connected, flash the patched firmware. The device should now mount as a drive, allowing you to delete the last added (and likely corrupted) files.

Finalize: After cleaning the storage, repeat the process using the ORIGINAL firmware setting in GarminCure3 to return the device to a factory state. 

Note: This is an unofficial tool. For official recovery methods, Garmin recommends using Garmin Express or performing a Master Reset using hardware button combinations. 

GarminCure3.exe is a third-party diagnostic utility used to unbrick Garmin GPS devices that are stuck in boot loops or fail to enter Mass Storage Mode. It works by patching original firmware to bypass the software checks that often cause crashes during the startup process. Core Functionality

The tool operates in two primary modes to help recover a device:

: Creates a modified firmware (RGN file) that prevents the GPS from loading its internal file system. This allows the device to stay on and be recognized as a removable drive

by your PC, so you can delete corrupted files (e.g., bad maps or GPX files). ORIGINAL Mode

: Used after you have cleared the corrupted files. It converts the original firmware back into a flashable RGN format to restore the device to its factory operating state. Standard Unbricking Workflow Preparation : Download the GarminCure3.exe tool and the official firmware ( ) for your specific model from the official Garmin website Generate Cure Firmware : Drag the GCD file into GarminCure3, select , and click Make firmware Enter Pre-Boot Mode

: Connect your device to your PC while holding a specific area of the screen (typically the top-left corner) to force it into "Pre-Boot" mode. Flash with Updater.exe Updater.exe

tool (usually included in the GarminCure3 zip) to flash the new "CURE" firmware to the device. Clean the Storage

: Once the PC recognizes the Garmin as a drive, delete recent or suspicious files. If the device is still unresponsive, some experts recommend formatting the drive using with FAT32 settings. Restore Original Firmware : Repeat the flashing process using the mode in GarminCure3 to return the GPS to normal operation. Zumo User Forums Critical Success Factors Pre-Boot Timing

: Entering pre-boot mode is the most difficult step; it often requires holding the screen corner the USB connection until the device is recognized. Driver Requirements Garmin USB Drivers are installed so Updater.exe can see the device over the USB interface. Device Compatibility

: The tool is widely tested on older automotive series such as nüvi 200, 13xx, 14xx, 24x0, and 37xx , as well as some Garmin Forums for your particular Garmin model? How To Unbrick A Nüvi | PDF | Games & Activities - Scribd

Garmin Express: A Comprehensive Overview

Garmin Express is a software application developed by Garmin, a leading manufacturer of GPS navigation devices, wearables, and other electronics. The software, also referred to as garmincure3exe, is designed to facilitate the management and maintenance of Garmin devices.

Key Features:

Benefits:

System Requirements:

Conclusion:

Garmin Express is a valuable tool for Garmin device owners, providing a centralized platform for managing and maintaining their devices. With its user-friendly interface and robust feature set, the software helps ensure devices operate at peak performance, while also protecting user data.

The air in the small lab was thick with the scent of ozone and desperation. Elias stared at the flickering screen, the progress bar for garmincure3.exe stuck at a grueling 99%. Outside, the digital plague—a self-replicating logic bomb that had already crippled the city's power grid—was literal minutes away from breaching the hospital’s backup generators.

"Come on," Elias whispered, his fingers hovering over the mechanical keyboard.

This wasn't just a patch; it was a Hail Mary. The "Full" version of the GarminCure script was rumored to be the only thing capable of untangling the recursive loops of the "Apex" virus. He had spent forty-eight hours scouring dark-web archives to find the complete executable, dodging automated sentries and encrypted firewalls.

Suddenly, the screen turned a deep, bruised purple. A terminal window snapped open, scrolling lines of amber code at a speed the human eye couldn't track.

GarminCure3.exe is a specialized, unofficial utility designed for Garmin devices, particularly when they are stuck in a "boot loop," stuck on the "Garmin Logo," or not recognized properly by a computer. It is part of the "cure" firmware method used by the community to force a device into a USB mass storage state for repair. ⚠️ Crucial Disclaimer

Use this at your own risk. This is a third-party tool, not official Garmin software. Improper use can permanently brick your device. This process will erase all user data (waypoints, routes, custom maps) on the device. 1. What is GarminCure3?

The GarminCure3.exe tool modifies a legitimate Garmin firmware update (.gcd file). It removes the bootloader check that prevents the device from starting, allowing the operating system (firmware) to flash even if the current system is corrupted. Typical Use Cases: Device stuck on startup screen (Garmin Logo). Device keeps restarting (Boot Loop).

Device not recognized as a drive when plugged into a computer (USB failure). Failed firmware update. 2. Prerequisites

GarminCure3.exe: Download the latest version (usually found on GPSPower forums or reputable Garmin repair forums).

Original Firmware (.gcd): You need the exact firmware file for your specific Garmin model.

Garmin USB Drivers: Ensure your computer has the necessary USB drivers installed via Garmin Express. PC: Windows environment. 3. Deep Guide: Using GarminCure3.exe Step-by-Step Phase 1: Preparing the "Cure" Firmware

Download & Extract: Extract the GarminCure3.zip file to a folder on your desktop.

Get the .gcd File: Download the original firmware for your device.

Tip: You can sometimes get this by running Garmin Express and looking in the temp folder, or downloading from authorized third-party archival sites. Run GarminCure3.exe: Right-click and Run as Administrator.

Load the Firmware: Click the ... button next to "Original firmware" and select your .gcd file.

Select CURE: Select the Cure radio button (as opposed to "Original"). Create Firmware: Click the Make button.

Result: A new Cure version of the file will be created in the same directory (usually named with _cure appended). Phase 2: Flashing the Device Prep the Device: Turn off your Garmin device. Force USB Mode:

Method A (Button): Hold the power/menu button (varies by model) while plugging the USB cable into the PC.

Method B (Force): Plug the cable in immediately after holding the power button to force the USB connection.

Verify Device Detection: The GarminCure3.exe window should now show the device in the dropdown list as "Pre-loader" or similar. Flash the Cure: Click the Flash button in the app.

Wait: Wait until the tool says "Finished" or "Success." Do not disconnect during this process. In dealing with executable files like GarminCure3

Unplug: Disconnect the USB cable. The device should now boot up into a basic USB mode. Phase 3: Finalizing Repair

Now that the device is running, it is in a "hacked" state (Cure Firmware) and won't behave normally. Plug in again: Connect the device back to the PC.

Remove Files: Navigate to the Garmin drive. You can now access the internal files. Delete the GARMIN\GarminDevice.xml file (if necessary, this forces a re-index). Flash Original Firmware:

Run GarminCure3.exe again, but this time select the Original radio button, load the original .gcd file, and flash it.

Alternatively, use Garmin Updater.exe to flash the original firmware over the cure firmware. Restart: Disconnect and turn on your device. 4. Troubleshooting

Device not recognized? Try a different USB cable (one that supports data, not just charging) and a different USB port on your PC (preferably USB 2.0).

Flash failed? Try running the tool in Windows 7/8 compatibility mode.

Still in boot loop? You may have selected the wrong firmware version, or the hardware itself is damaged.

If this guide didn't fully resolve your issue, it would be helpful to know: What is the exact model of your Garmin device?

What is the symptom (e.g., stuck on Garmin logo, or fully black screen)?

Does your computer make a sound when you plug it in, even if it doesn't show a drive?

I can then help identify if this is a software fix or a hardware issue.

The Ultimate Guide to GarminCure3.exe: Unlocking the Full Potential of Your Garmin Device

As a Garmin device user, you may have come across the term "GarminCure3.exe" while searching for solutions to common issues or seeking to unlock the full potential of your device. In this comprehensive article, we will delve into the world of GarminCure3.exe, exploring its purpose, functionality, and benefits. By the end of this article, you will have a thorough understanding of GarminCure3.exe and how it can enhance your Garmin experience.

What is GarminCure3.exe?

GarminCure3.exe is a software tool designed to repair, update, and configure Garmin devices. The "exe" extension indicates that it is an executable file, which can be run on Windows operating systems. This software is not an official Garmin product but rather a third-party tool developed by enthusiasts and experts to help users troubleshoot and optimize their Garmin devices.

What problems can GarminCure3.exe solve?

GarminCure3.exe can help resolve a variety of issues common to Garmin device users, including:

How does GarminCure3.exe work?

When you run GarminCure3.exe, the software performs a series of checks and operations to diagnose and repair issues with your Garmin device. Here's a general overview of the process:

Benefits of using GarminCure3.exe

The benefits of using GarminCure3.exe include:

Downloading and using GarminCure3.exe

To download GarminCure3.exe, you can search for the file on reputable software download websites or forums dedicated to Garmin devices. Be sure to download the file from a trusted source to avoid malware or viruses.

Once downloaded, follow these steps:

Safety precautions and warnings

When using GarminCure3.exe, keep in mind:

Conclusion

GarminCure3.exe is a powerful tool that can help you unlock the full potential of your Garmin device. By providing a comprehensive troubleshooting and repair solution, this software can save you time and effort while ensuring your device runs smoothly and efficiently. While using GarminCure3.exe, remember to exercise caution and follow safety precautions to avoid any potential risks. With this guide, you are now equipped to explore the world of GarminCure3.exe and take your Garmin experience to the next level.

For users looking for "GarminCure3.exe full," this typically refers to the GarminCure3 tool

, a popular utility used to recover ("unbrick") Garmin GPS devices that are stuck in a reboot loop or failing to load. Recovery Instructions for GarminCure3

To use this tool safely to fix a bricked device, follow these steps derived from community guides: Preparation : Download GarminCure3.exe Updater.exe . You also need the official firmware file ( ) for your specific device model from the Garmin Support website Create Cure Firmware Open GarminCure3.exe and drag your firmware file into the "Input file" box. Select the option and click Make firmware Enter Pre-Boot Mode Turn off your Garmin device.

Hold the "Pre-boot" key (often the top-left corner of the screen or a specific physical button like 'Up') and connect it to your PC. Flash the Firmware Updater.exe

(or click the button in GarminCure3) and select the "USB Device" option once your device is recognized. Enable Mass Storage

: Once the "CURE" firmware is flashed, the device should be recognized by your PC as a drive. This allows you to delete corrupt files (like problematic files) that caused the brick. Restore Original Firmware

: After cleaning the storage, repeat the process in GarminCure3 but select to flash the device back to its standard operating state. Safety Warning

Be cautious of sites offering "full" versions of this tool that include extra executable files. There is no official "pro" or "full" paid version; the standard tool is community-developed and free. Downloads from unverified sources may contain malware designed to steal credentials or monitor activity. for a particular Garmin model? AI responses may include mistakes. Learn more How To Unbrick A Nüvi | PDF | Games & Activities - Scribd

GarminCure3.exe is a specialized firmware patcher designed to unbrick Garmin devices that are stuck in a "boot loop" or won't start past the logo screen. It works by creating a modified version of the device's firmware, known as "CURE" firmware, which forces the device to enter Mass Storage Mode immediately upon booting, bypassing the normal startup processes that typically cause crashes. Key Features and Functionality

Mass Storage Access: Patched "CURE" firmwares do not load maps or system files during startup, allowing a PC to recognize the bricked device as a standard flash drive.

File Corruption Curing: Once Mass Storage Mode is active, users can delete or rename corrupted files (like faulty maps or GPX files) that were preventing a normal boot.

NTFS Support: The tool can function even if a device's internal filesystem was accidentally formatted to NTFS.

Device Compatibility: While originally tested on various Garmin nüvi models (200, 6x0, 13xx, 14xx, 22x0, 24x0, 37xx), it has been used effectively on other handhelds like the eTrex 30. Step-by-Step Recovery Process

The unbricking process generally involves two main phases: enabling file access and restoring original functionality. Phase 1: Flashing the "CURE" Firmware

Preparation: Download GarminCure3.exe and Updater.exe into the same folder. Ensure you have the Official Garmin USB Drivers installed. Benefits:

Input Firmware: Obtain the original firmware file (.GCD) for your specific model from the Garmin website. Drag and drop this file into the "Input file" box in GarminCure3.

Create Patch: Select the CURE option and click Make firmware.

Enter Pre-boot Mode: Power off the device. While holding a specific key or screen corner (varies by model, e.g., holding the top-left corner of the nüvi screen), connect it to your PC via USB.

Flash: Open Updater.exe from within GarminCure3, select USB Device, and click OK while the device is still in pre-boot mode. Phase 2: Fixing and Restoring

File Cleanup: Once the "CURE" firmware is flashed, the device should appear as a drive on your PC. Locate and remove the corrupted file that caused the crash.

Format (Optional): If deleting files doesn't work, tools like RMPrepUSB can be used to reformat the internal storage to FAT32.

Restore Original Firmware: Run GarminCure3 again, but this time select the ORIGINAL radio button. Repeat the flashing process to return the device to its factory software state. Troubleshooting Common Issues

Connection Errors: If Updater.exe fails to recognize the device, try running it as an administrator or check for faulty USB cables.

Pre-boot Windows: The "pre-boot" window is often very short; you must click "OK" in the Updater tool immediately after the device is recognized.

Missing System Folders: If the device connects but you cannot see the .System folder, ensure your PC's folder options are set to "Show hidden files, folders, and drives".

For official software updates that do not require unbricking, Garmin recommends using standard tools like Garmin Express or WebUpdater. JustAnswerhttps://www.justanswer.com

Garmin’s ecosystem historically includes applications like Garmin Express, Garmin Connect, and device-specific utilities that perform tasks including:

A binary named GarminCure3.exe plausibly fits within the update/repair component family (the name suggests "cure"/repair or update routines). Such components often run with elevated privileges or as services to modify device firmware or system drivers.

To study GarminCure3.exe without executing it, follow these steps:

Only attempt if you fully understand the risks.

Q: Is Garmin’s official software safe?
A: Yes, Garmin Connect and Garmin Express are safe to use directly from the Garmin website.

Q: What if I can’t remove GarminCure3.exe?
A: Use a dedicated malware removal tool or consult a professional.

Q: Can it damage my Garmin device?
A: It may disrupt device connectivity or corrupt firmware. Always use trusted software.

Stay Safe Online! Always verify unknown executables and avoid downloading software from third-party sites. 🛡️

If you believe your device is compromised, run a scan now.

GarminCure3.exe is a third-party software utility designed to "unbrick" or recover Garmin GPS devices that have become unresponsive, often due to corrupted firmware or faulty map files. While it is a legitimate tool within the niche GPS repair community, it is not an official product of Garmin International. The Role of GarminCure3.exe in Device Recovery

Garmin devices occasionally enter a "boot loop" or get stuck on the splash screen because they cannot process a specific corrupted file during the startup sequence. Because the device never fully boots, it often isn't recognized by a computer as a standard USB mass storage drive, preventing the user from deleting the problematic file. GarminCure3 solves this by:

Patching Firmware: It takes an original firmware file (a .gcd file) and modifies it to create a "CURE" version.

Forcing Mass Storage: When this "CURE" firmware is flashed to the device, it prevents the unit from trying to load its internal files. This forces the device to stay in a state where a computer can recognize it as a drive.

Enabling Repair: Once recognized, users can manually delete corrupted maps, waypoints, or system files that were causing the crash. The Technical Process

Using this tool is a multi-step procedure that carries significant risk if done incorrectly. How to Brick a Garmin eTrex30 by a Simple Waypoint Upload

Understanding the Garmincure3.exe Tool for GPS Device Recovery

Garmin GPS devices are renowned for their reliability, but software glitches can sometimes render them unusable. One of the most effective tools for reviving a "bricked" Garmin device is the Garmincure3.exe utility. This article provides a comprehensive overview of the tool, its functions, and how to use it safely. What is Garmincure3.exe?

Garmincure3.exe is a specialized software utility designed to help users recover Garmin handheld and automotive GPS devices that have encountered critical software errors. Common issues include the device getting stuck on the logo screen, constant reboot loops, or being unable to communicate with a computer via USB.

The utility works by creating a "cured" version of the device's firmware. This modified firmware allows the device to boot into a limited state where the internal storage can be accessed and repaired, even if the primary operating system is corrupted. Key Features of Garmincure3.exe

Simple User Interface: The tool is designed with a straightforward layout, making it accessible even for those who are not highly technical.Firmware Patching: It automates the process of patching original Garmin firmware (.gcd files) to create a bootable "cure" version.Mass Storage Mode Access: Its primary goal is to force the device into Mass Storage Mode, allowing users to delete corrupt files (like GPX logs or map files) that prevent a normal boot.Compatibility: It supports a wide range of older and modern Garmin models. How to Use Garmincure3.exe Safely

Using firmware modification tools always carries a small risk. Follow these steps to ensure the best results:

Identify Your Firmware: Determine the exact model and current firmware version of your Garmin device.

Download Original Firmware: Locate the official Garmin .gcd firmware file for your specific device from trusted archives.

Prepare the Cure: Open Garmincure3.exe, load the .gcd file, and select the "Cure" option to generate the modified firmware.

Flash the Device: Use the updater.exe tool (often bundled or required alongside Garmincure3) to send the cured firmware to your device while it is in "Pre-Boot" mode.

Clean the Filesystem: Once the device is recognized as a drive on your computer, remove the corrupt files.

Return to Original Firmware: After cleaning the device, repeat the process using the "Original" setting in Garmincure3.exe to restore the device to its factory software state. Precautions and Risks

Battery Level: Ensure your device has at least 50% battery or is plugged into a reliable power source during the flashing process.Correct Model: Never attempt to flash firmware intended for a different Garmin model, as this can cause permanent hardware damage.Backup: If possible, always back up your personal data and maps before attempting a firmware recovery. Conclusion

The Garmincure3.exe utility is an invaluable resource for DIY enthusiasts looking to save their Garmin devices from the scrap heap. By understanding how to properly patch and flash firmware, you can overcome many software-related failures and extend the life of your navigation hardware. If you'd like more specific instructions for your device:

Provide your Garmin model name (e.g., Oregon 600, Nuvi 2595). Describe the exact error or screen you are seeing.

I can then walk you through the specific pre-boot sequence and file cleanup steps for your hardware.

Updated June 2024

For vendors:

For administrators and users: