At first glance the SpeedStile FL reads as a minimalist corridor of glass and stainless steel. Its slim profiles and clear glazing aim to preserve sightlines while channeling pedestrians. The design intent informs every installation decision: foundations are compact but exact; cabling is hidden yet accessible; tolerances are tight so the glass wings close softly and reliably. Understanding that intent anchors installation choices: keep sightlines clear, mount controls where technicians can service them without disrupting public flow, and align panels and pathways for an intuitive approach.
The Gunnebo SpeedStile FL is not a temperamental device. It’s precise. If you rush, it will humiliate you with false alarms. If you’re methodical, it will move 60 people per minute without breaking eye contact.
Respect the manual. Trust the torque specs. And when that first commuter glides through without breaking stride… you’ll know why you do this.
Gate closed. World locked. You’re good. 🔒
This blog post draft focuses on the Gunnebo SpeedStile FL , a high-performance flap-leaf speed gate. It breaks down the critical installation steps and technical requirements found in official documentation from sources like Gunnebo Entrance Control and Siel Invest. Streamlining Security: A Quick Guide to Gunnebo SpeedStile FL Installation Installing a high-end security barrier like the Gunnebo SpeedStile FL
requires precision to ensure long-term reliability and peak performance. Whether you are setting up a standard 600mm lane or a 900mm wide ADA-compliant passageway, following the manufacturer’s technical guidelines is essential. 1. Site Preparation & Foundation
Before unboxing, the installation site must meet specific structural requirements:
Floor Leveling: The base must be flat and level to within +/- 5mm across the entire footprint to prevent mechanical strain.
Concrete Quality: Use concrete with a minimum resistance of 30N/mm².
Bolting Depth: Secure the unit with a minimum bolting depth of 70mm.
Conduits: Run under-floor conduits (minimum 20mm diameter) at least 140mm below the finished floor level, ensuring they rise 50mm from the foundation into the cabinet. 2. Mechanical Installation SpeedStile FL
is typically delivered pre-assembled but may require lifting equipment due to its weight—side cabinets can weigh approximately 135kg and center cabinets 150kg.
Cabinet Alignment: For multi-lane setups, align your Left (L), Center (C), and Right (R) cabinets carefully to ensure synchronized flap movement. gunnebo speedstile fl installation manual
Pre-Power Check: Manually rotate the glass panels before connecting power. Check for low oscillation; high movement without encoder motion can indicate mechanical issues. 3. Electrical & Logic Setup
Installation O peration and Maintenance Manual - Siel Invest
Gunnebo SpeedStile FL Installation & Manual Guide The Gunnebo SpeedStile FL
(Flap Leaf) is a high-performance security gate designed for seamless entrance control in corporate, governmental, and public environments. This guide provides a comprehensive overview of the installation process, technical requirements, and operational maintenance based on official documentation from Gunnebo Entrance Control. 1. Site Preparation & Foundation Requirements
Before unboxing the units, ensure the installation site meets the following structural and spatial requirements:
Floor Quality: The foundation must be a flat, level concrete base with a minimum resistance of fck(cube) 30N/mm².
Dimensions: The base area should be at least 1300mm to 2000mm long (depending on cabinet model) and 400mm to 500mm wide.
Levelling: The floor must be level within +/- 5mm over the entire footprint.
Conduits: Any horizontal conduits running below the SpeedStile must be at least 140mm below the Finished Floor Level (FFL). 2. Technical Specifications SpeedStile FL
is available in several configurations, most notably the BA (square ends) and EV (rounded ends) versions. Standard Configuration Wide (ADA) Configuration Passage Width Cabinet Length 1500 mm or 1925 mm 1500 mm or 1925 mm Cabinet Height Power Supply 230VAC 50Hz (115VAC 60Hz available) 230VAC 50Hz (115VAC 60Hz available) Power Rating 60VA Standby / 300VA In Operation 60VA Standby / 300VA In Operation 3. Installation Step-by-Step
Follow these procedures to ensure the units are aligned and secured correctly: Gunnebo SpeedStile FL
Feature: Gunnebo SpeedStile FL Installation Manual At first glance the SpeedStile FL reads as
Introduction
The Gunnebo SpeedStile FL is a high-speed, bi-directional pedestrian gate designed for secure and efficient access control. Proper installation of the SpeedStile FL is crucial to ensure optimal performance, reliability, and safety. This feature provides a comprehensive guide for installing the Gunnebo SpeedStile FL, including step-by-step instructions, technical specifications, and important safety considerations.
Pre-Installation Checklist
Before beginning the installation process, ensure that:
Installation Steps
Technical Specifications
Safety Considerations
Conclusion
The Gunnebo SpeedStile FL is a reliable and efficient pedestrian gate solution for secure access control. By following this installation manual, you can ensure a successful installation and optimal performance of the SpeedStile FL. If you have any questions or concerns, please consult the Gunnebo support team or a qualified installation professional.
Appendix
The Gunnebo SpeedStile FL installation requires precise site preparation, specialized electrical wiring, and the configuration of programmable relays to ensure secure pedestrian access control. 1. Site Preparation & Mounting
To ensure structural integrity and smooth operation, the installation site must meet these specific physical requirements: Installation Steps
Foundation: A flat and level finished floor with a tolerance of +/- 5mm is required.
Concrete Strength: The base should be concrete with a minimum resistance of fckcube 30N/mm².
Bolting Depth: Anchors must reach a minimum depth of 70mm into the concrete.
Cabinet Dimensions: The foundation area for a standard unit should be at least 2000mm x 500mm x 150mm deep.
Conduits: Cable conduits must run at least 140mm below the finished floor and rise at least 50mm from the foundation level. 2. Electrical Requirements
All electrical work must be performed by authorized personnel according to the manual's specifications.
Power Supply: Standard 230Vac, 50Hz (with a 115Vac, 60Hz option available). Power Consumption: Standby: Approximately 60VA to 120VA. In Operation: Up to 300VA to 345VA. Logic Voltage: Operates on 24V DC.
Fire Alarm Interface: Requires a voltage-free contact input to trigger the fail-state (opening the leaves) in emergencies. Gunnebo SpeedStile FL
REPORT: Gunnebo SpeedStile FL Installation Manual
Subject: Overview of Installation Procedures and Technical Specifications for Gunnebo SpeedStile FL Speed Gates.
Date: October 26, 2023 Prepared By: Technical Documentation Review