Only use this specific file if:
Warning: Do not use rev0010 on newer Cloud II headsets (2020+, especially the wireless Cloud II or “Cloud II Core”). It may brick the USB dongle.
The official firmware updater for the HyperX Cloud II is a Windows executable that updates the firmware on the USB sound card (dongle) that comes with the headset. The headset itself is analog (3.5mm jacks), but the USB dongle contains a digital signal processor (DSP). Firmware updates apply to that dongle.
Typical changes in firmware updates include:
The last widely acknowledged official firmware for Cloud II (before HyperX moved to NGENUITY software) was version 0010 or later 0030 for some revisions. This is where “rev0010” in the filename suggests revision 0010.
The hyperx_cloudii_firmware_updater_rev0010.exe (2021) is a legacy tool – useful in specific edge cases, but outdated for most users. If your Cloud II is working fine, leave the firmware alone. If you must update, get the newest version from HyperX directly.
Safe updating, and happy gaming. 🎧
Disclaimer: This post is for informational purposes. Always follow official HyperX instructions. Firmware updates carry a small risk; ensure your device is backed up (if applicable) and power is stable.
HyperX Cloud II Firmware Updater Rev 0010 is a legitimate official update for the wired Cloud II USB sound card. While it is primarily intended to improve PS4 compatibility microphone issues
, its release has caused significant confusion among users due to numbering inconsistencies. Key Takeaways Version Confusion:
Many users are confused because their headsets often ship with version
appear to be a downgrade. HyperX has confirmed that "0030" was a naming typo (meant to be 0003) and that 0010 is the newer, official version Primary Benefits: Adds or improves compatibility with the Resolves certain microphone detection or low volume issues. Safety & Legitimacy:
The file is safe and official when downloaded from authorized sources like the official HyperX support site User Experience & Potential Issues Low Audio:
Some users report that after updating, the overall sound volume may become lower, though this can often be corrected with third-party equalizer software. Hardware Compatibility: This specific updater is generally for the older (Kingston-era) wired models
. Newer HP-manufactured versions of the Cloud II may require a different firmware (such as ) and might not be detected by this 0010 updater. Stuttering:
A small number of users reported audio stuttering issues after updating, with no easy way to roll back to previous versions. Installation Best Practices If you choose to run the updater, follow the official update procedure
HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe is an official utility used to update the firmware of the HyperX Cloud II USB sound card to version
. This specific version was released to provide compatibility for the Sony PlayStation 4 (PS4) Key Update Details
Enhances the USB sound card to support PS4 audio and controls. Release Context:
While version numbers like 0030 exist, official documentation and community consensus confirm that 0010 is the newer, stable version for the original Kingston-era Cloud II headsets. Installation Steps Plug your Cloud II USB sound card into a PC.
file. The interface will display your current version and the target version (0010). Click "Update." Do not unplug the device during this process to avoid bricking it. Power Cycle:
Once finished, unplug the USB sound card and plug it back in to activate the new firmware. Driver Reset:
It is recommended to uninstall the "HyperX 7.1 Audio" device from Windows Device Manager
and restart your computer to let Windows reload the fresh driver. Important 2021+ Compatibility Note
Complete Guide to HyperX Cloud II Firmware Updater Rev 0010 (2021)
The HyperX Cloud II Firmware Updater Rev 0010 is a critical software utility designed to update the firmware of the HyperX Cloud II gaming headset's USB sound card. While originally released under the Kingston era, this specific revision remained the standard "modern" update for many users throughout 2021 to ensure compatibility with newer gaming consoles and operating systems. Why You Need Revision 0010
Updating to Rev 0010 is primarily essential for users who want to use their HyperX Cloud II with the Sony PlayStation 4 (PS4). This firmware enables the 7.1 virtual surround sound and volume controls to function correctly on the console, which may not work with older firmware versions like 0005. Additionally, keeping your firmware updated can:
Resolve bugs: Fixes common audio dropouts and latency issues.
Improve compatibility: Ensures the headset works seamlessly with Windows 10 and 11.
Performance: Maintains peak audio and microphone performance. How to Use HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe
Follow these steps carefully to update your device. Warning: Do not disconnect the headset during this process, as it can "brick" the USB sound card.
Comprehensive Review: HyperX Cloud II Firmware Updater (Rev 0010, 2021) The HyperX Cloud II
remains one of the most iconic gaming headsets ever made, but even legendary hardware needs software refinement. The Rev 0010 firmware update, released in late 2020 and widely adopted throughout 2021, was a pivotal utility designed to modernize the headset's USB sound card performance for the latest generation of consoles and PC operating systems. Purpose and Compatibility
The primary mission of the HyperXCloudIIFirmwareUpdaterRev0010.exe file was to provide PlayStation 5
and PlayStation 4 compatibility for the USB control box. Before this specific revision, many users reported volume issues or complete lack of recognition when plugging the Cloud II into Sony's newer consoles.
Primary Fix: Enables full plug-and-play support for PS5 and PS4. Secondary Goal: General stability improvements for Windows 10/11 and macOS. Target Device: Only the Cloud II (Wired) hyperxcloudiifirmwareupdaterrev0010 exe file 2021
version with the included 7.1 Virtual Surround Sound USB dongle. The Installation Experience
Running the updater is a refreshingly "old-school" experience. There is no heavy hub software like NGENUITY required for this specific legacy fix.
Simplicity: The .exe is a standalone tool. You plug in your USB dongle, run the file, and it detects your current version versus the "New Version" (0010).
Risk Factor: As with all firmware updates, there is a minor risk of "bricking" the dongle if the cable is unplugged during the 30-second flash. However, the 0010 updater proved to be highly stable compared to earlier iterations.
Visual Interface: It’s a basic grey window. It’s not pretty, but it’s functional and lightweight. Performance & Sound Changes
Unlike some firmware updates that mess with EQ profiles, Rev 0010 stays faithful to the original sound signature.
7.1 Virtual Surround: The update maintains the signature 7.1 toggle functionality without adding extra latency.
Mic Quality: Some users noted a slight reduction in "static hiss" when using the mic monitoring (if enabled via Windows), though this wasn't an officially documented fix.
Console Volume: This is where the update shines. It fixes the "low volume" bug on PS4/PS5, ensuring the hardware buttons on the dongle actually scale the audio correctly within the console's OS. The Downsides
The biggest hurdle is accessibility. HyperX’s transition under HP ownership made finding these legacy firmware files slightly more difficult on the official website for a period. Additionally, this update does nothing for the headset if you are using the 3.5mm jack directly; it is strictly a "brain transplant" for the USB sound card.
The 2021 Rev 0010 Firmware is an essential "quality of life" update. If you are a console gamer or experiencing weird "device not recognized" errors on a modern PC, this file is the cure. It’s a zero-fluff utility that does exactly what it promises: keeps a 2015-era headset relevant in a 2026 gaming landscape.
HyperX Cloud II Firmware Updater Rev 0010: Essential Guide for 2021 and Beyond
The HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe is a critical software utility for users of the original Kingston-era HyperX Cloud II headset. While newer versions of the headset often use the HyperX NGENUITY software for updates, the Rev 0010 standalone file remains the definitive solution for older units to ensure system compatibility and performance. Why You Need Firmware Revision 0010
Firmware is the embedded software that manages the headset's hardware functions. Revision 0010 was specifically released to address several core areas:
PlayStation 4 Support: This update famously added official support for the Sony PS4 console, allowing users to use the USB sound card directly with the system.
Audio Stability: It provides fixes for common issues like audio dropouts and microphone static.
System Compatibility: It ensures the USB sound card communicates effectively with modern operating systems like Windows 10 and 11. Preparation Checklist
Before running the updater, you must follow these safety steps to avoid "bricking" your device:
Direct Connection: Connect the Cloud II USB sound card directly to your motherboard's USB port. Do not use a USB hub.
Headset Disconnection: Unplug the 3.5mm headset jack from the USB sound card before starting the update.
Power Stability: Ensure your computer will not lose power during the process. Disconnecting the device during the update can make it permanently unusable. How to Use the Rev 0010 Firmware Updater Follow these steps to apply the update manually:
Launch the Utility: Double-click the HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe file.
Compare Versions: The interface will display your current firmware version and the new version. If you see a message stating your current version is newer, you can usually click "No" to cancel.
Execute Update: Click the Update button. A progress bar will track the installation.
Power Cycle: Once you see the "Firmware updated successfully" message, click OK. You must then unplug and reconnect the USB sound card to finish the process.
Driver Reload: For the best results, open Device Manager on your PC, uninstall the "HyperX audio device" under "Sound, video and game controllers," and then reconnect the device to reload the Windows drivers. Troubleshooting Common Issues
HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe is a critical utility released in
to address hardware compatibility and performance issues for the HyperX Cloud II
The most common "story" surrounding this specific file involves users who purchased headsets after HP acquired HyperX in 2021. Because the hardware was updated during the transition, many older firmware versions would no longer recognize newer USB dongles, leading to the infamous "HyperX Cloud II Device not found" The Update Story: Revision 0010
The Rev 0010 update was designed to solve several core issues: HP Hardware Compatibility
: It updated the USB sound card drivers to recognize headsets manufactured under the new HP branding (VID_03F0). PlayStation 5 Support
: It improved the headset's performance and volume levels when used with PS5 consoles.
: Addressed common issues like audio popping or the sound card not being detected after a system reboot. How to Use the Updater
If you are still looking to run this specific update, follow these steps derived from the official instruction guide Preparation
: Ensure your HyperX Cloud II USB sound card is plugged directly into a USB port on your PC (avoid hubs). : Open the HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe Check Version Only use this specific file if:
: The interface will display your current firmware version vs. the new version (0010). : Click the
button. Even if it says your version is the same, you can click "Yes" to re-flash the firmware if you are experiencing bugs. Power Cycle
: Once the "Firmware updated successfully" message appears, you
unplug the USB sound card and plug it back in for the changes to take effect. Troubleshooting Tips Device Not Found
: If the updater doesn't see your headset, you likely have a newer "HP-branded" version. According to community discussions on , these units may require different drivers or the HyperX NGENUITY software instead of the standalone
: Never unplug the headset while the progress bar is moving, as this can permanently disable the USB sound card. If you'd like, I can help you: official download link for this specific file. Troubleshoot why your PC isn't recognizing the headset even after the update. Check if your headset is the HP or Kingston
This is a detailed, investigative look into the file you’ve referenced:
hyperxcloudiifirmwareupdaterrev0010.exe (associated with the year 2021).
This would help users diagnose why the tool says "Device not found" even when the headset is plugged in.
Note: If you still have this .exe, be aware that HyperX has since released newer updaters (rev0020+). The 2021 version may fail on Windows 11 24H2 or newer.
Title: HyperX Cloud II Firmware Updater Rev 0010 (2021 Release): Overview and Advisory
Introduction The file HyperXCloudIIFirmwareUpdaterRev0010.exe refers to a specific software utility released by HyperX (formerly a division of HP, originally Kingston) designed to update the internal firmware of the HyperX Cloud II gaming headset. This specific revision, released around 2021, was a critical update for users experiencing hardware recognition issues, particularly after major Windows updates.
Purpose of the Update The HyperX Cloud II is a highly popular gaming headset known for its durability and sound quality. However, as operating systems evolve, the internal driver software within the headset’s USB sound card occasionally requires patching to maintain compatibility.
The primary functions of the Rev 0010 firmware updater included:
Installation Process The utility is a standalone executable, meaning it generally does not require a full software suite installation to run. The typical process for this specific revision involves:
Critical Advisory: Driver vs. Firmware A common point of confusion for users in 2021 was the distinction between the Firmware Updater and the USB Driver.
The Rev 0010 update was specifically for the firmware. If a user installed this but still had issues, they often needed to manually update the "HyperX Virtual Surround Sound" driver within Windows Device Manager. Microsoft's automatic driver updates frequently conflicted with the older HyperX drivers, leading many users to mistakenly believe the firmware update failed.
Safety and Security Warning As this file dates back to 2021, users attempting to locate it today should exercise caution:
Conclusion The HyperXCloudIIFirmwareUpdaterRev0010.exe file represents a significant maintenance patch in the product's lifecycle. While essential for fixing compatibility bugs in 2021, users today should ensure they are downloading the correct version for their specific hardware revision and should prioritize official sources to ensure system security.
The HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe (often released around 2021) is more than just a boring driver update—it is the "doctor" that has saved thousands of Cloud II headsets from a silent death. This specific firmware, particularly for the USB sound card, was designed to address mic volume issues, low audio, and 7.1 surround sound recognition issues in Windows.
Here is an interesting review of this crucial (and sometimes treacherous) update. The "Rev 0010" Story: A Life-Saver HyperX Cloud II
first launched, its USB dongle sometimes failed to communicate properly with newer Windows versions, leading to incredibly faint microphone audio that made it unusable for gaming communication.
The Fix: This update bridges that gap. It flashes the USB dongle with new instructions, bringing the mic level from "hardly audible" to a solid, usable volume.
The 7.1 Boost: It helps ensure Windows actually recognizes the device as a 7.1 audio source rather than just basic stereo, allowing the button on the dongle to properly activate surround sound. The Good & The "Risky"
The Good: If your microphone is dead, this firmware often resurrects it without requiring a brand-new headset purchase.
The Bad: The installation process is notoriously finicky. If you have the HP-branded version of the headset, you must use the HP-specific update; using the older Kingston version can break it.
The Risk: As with all firmware updates, interrupting this process (e.g., unplugging the USB while it's flashing) can "brick" the dongle, turning it into a useless piece of plastic. Verdict: Proceed with Caution, but Proceed Go to product viewer dialog for this item.
(wired version) is working perfectly, do not update. This is a "fix it if it's broken" situation.
However, if your microphone volume is too low to use, or the 7.1 surround button isn't working, this is mandatory. Just ensure you carefully follow the official Kingston instructions, and it will likely solve your issues. If you're having trouble with the update, let me know:
Do you have the original Kingston version or the newer HP version of the headset?
Are you getting a specific error message when you try to run the .exe file?
I can help identify the exact version you need or look for a workaround. HyperX Cloud 2 Microphone Low Audio Fix w/ firmware update
What is HyperX Cloud II Firmware Updater Rev.0010.exe?
The HyperX Cloud II Firmware Updater Rev.0010.exe is an executable file that updates the firmware of the HyperX Cloud II gaming headset. The file is specifically designed for updating the firmware to version 0010.
Purpose of the firmware update:
The firmware update is intended to improve the performance, stability, and functionality of the HyperX Cloud II headset. The update may include:
How to use the HyperX Cloud II Firmware Updater Rev.0010.exe:
To update the firmware of your HyperX Cloud II headset using the HyperX Cloud II Firmware Updater Rev.0010.exe file:
Troubleshooting tips:
If you encounter issues during the update process:
Conclusion:
The HyperX Cloud II Firmware Updater Rev.0010.exe file is a utility designed to update the firmware of the HyperX Cloud II gaming headset. By following the steps outlined above, you can successfully update your headset's firmware to improve performance, stability, and functionality. If you encounter any issues, refer to the troubleshooting tips or contact HyperX support for assistance.
The HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe file is a official firmware update designed primarily for the wired version of the HyperX Cloud II headset. While originally released to improve compatibility with the PlayStation 4, it remains a common point of research for users troubleshooting issues like mic static or audio detection on newer systems like Windows 10 and 11. Key Features & Purpose
PS4 Compatibility: The primary reason for the "0010" update was to enable volume control and 7.1 surround sound functionality when the USB sound card is used with a PS4.
Bug Fixes: It addresses common "legacy" issues such as low microphone volume or static coming from the USB sound card.
Version Clarification: There is a known typo in some production units where they appear to have version 0.0.3.0. HyperX has clarified this is actually 0.0.0.3, meaning 0010 is indeed a newer and recommended update. Critical Compatibility Alert (HP vs. Kingston)
In 2021, HP acquired HyperX. This caused a split in firmware compatibility: Kingston Models: Use the Rev 0010 updater.
HP Models (Post-2021): These units often have HP branding on the headband and use a different vendor ID (VID_03F0). If you have an HP-manufactured unit, the 0010 updater may fail to detect your device. You may need version 4103 or later, which is often found via the HyperX Support Page. Installation Procedure
Direct Connection: Plug the USB sound card directly into a motherboard port (avoid USB hubs).
Disconnect Headset: Keep the 3.5mm headset jack unplugged from the USB dongle during the update process.
Run Updater: Open the .exe file. It will show your current version and the target (0010).
Power Cycle: Once finished, unplug the USB dongle and plug it back in to finalize the changes. User Concerns & Potential Risks
Bricking Risk: If the update is interrupted (power loss or cable unplugged), the USB sound card can become permanently unusable.
7.1 Loss: Some Windows users report the 7.1 surround sound button stops working after updating. This often requires a driver reinstall through the Windows Device Manager.
Alternative Method: If the standalone .exe fails, you can use the HyperX NGENUITY software from the Microsoft Store, which can automatically detect and update many newer versions of the headset.
The HyperX_Cloud_II_Firmware_Updater_Rev_0010.exe file is a standalone update utility for the HyperX Cloud II (wired) Go to product viewer dialog for this item.
USB sound card. Released around 2021, its most "helpful feature" is resolving critical microphone issues, specifically fixing low microphone volume levels. Key Benefits of Rev 0010
Microphone Fix: Addresses the "low mic audio" bug common in older firmware versions.
Virtual Surround Sound: Ensures the 7.1 virtual surround sound processing is optimized for modern Windows environments.
OS Compatibility: Improves stability and reduces audio dropouts on Windows 10 and 11. Important Compatibility Warning
Be careful before running this specific .exe file. There are two versions of the
Kingston Models: These are older and fully compatible with the Rev 0010 updater.
HP Models: Headsets manufactured after HP acquired HyperX (identifiable by the HP logo on the box or specific serial numbers) often require Firmware 4103. Using Rev 0010 on an HP-branded model may fail to detect the device or cause errors. How to Use the Updater HyperX Cloud 2 Microphone Low Audio Fix w/ firmware update
HyperX Cloud 2 Microphone Low Audio Fix w/ firmware update - YouTube. This content isn't available. YouTube·mrgencal HyperX Cloud II FW Update 0010 Procedure
Step 1: Applying the new firmware. 1. Launch the update utility by double clicking the HyperX_Cloud_II_Firmware_Updater_Rev_0010 . Kingston Technology
When run legitimately:
Does NOT:
File hash comparison
Official firmware updater SHA-256 (example – do not trust blindly):
F9A3C8E1... (You must get this from HP’s official support site.)
VirusTotal scan
Upload the file to VirusTotal (virustotal.com). If more than 3–5 engines flag it as malicious, it’s malware.
Origin
Did you download it from https://www.hyperx.com/pages/support or https://support.hp.com?
If not, treat it as suspicious. Warning: Do not use rev0010 on newer Cloud
// Function: FlashFirmware()
// Implements the SafeState logic
bool FlashFirmware(Device target, File firmware)
// 1. Environment Check
if (CheckUSBPower() < REQUIRED_AMPERAGE)
return Error("Insufficient USB Power. Try a rear port.");
// 2. Lock Device Resources
if (!LockUSBEndpoint(target))
return Error("Device busy. Close Discord/Razer Synapse.");
// 3. Write in Chunks with Verification
while (bytesWritten < totalSize)
// Write chunk
WriteBlock(target, buffer);
// Immediate Read-Back Verification
byte[] readBack = ReadBlock(target);
if (readBack != buffer)
// CRITICAL: Mismatch detected
LogError("Write verification failed at offset: " + bytesWritten);
TriggerSafeState(target); // Force reset to bootloader
return Error("Write failed. Device reset to Safe Mode. Please retry.");
UpdateProgressBar(bytesWritten);
// 4. Finalize
target.Reboot();
return Success;
For Cloud II users, the main fixes/enhancements historically included:
Without the original release notes for rev0010, the changes likely addressed bugs from earlier revs (e.g., rev0008, rev0009) and possibly compatibility with Cloud II’s “new” colors or special editions.