Simco Fmx002 Manual Full <PREMIUM - 2026>
The manual dedicates an entire page to zero adjustment. Why? Because the FMX-002 measures fields relative to its own reference. If it is not zeroed, every reading will be off by an offset value.
Procedure from the full manual:
Do not skip this step. The manual warns that zeroing should be performed every time the device is turned on after a battery change or temperature shift.
For the complete safety warnings (including explosion hazards near flammable solvents) and the full schematic, download the PDF below.
[Click Here to Download: simco_fmx-002_manual_full.pdf] (Replace with actual link)
File size: ~1.2 MB Language: English (German/French appendices included in full version)
Have a specific issue with your FMX-002? Leave a comment below. Many users have successfully revived "dead" units by simply cleaning the battery terminals—something the manual covers in section 6.4.
Disclaimer: Always refer to the original manufacturer documentation for safety and calibration standards.
Simco FMX-002 is a portable electrostatic fieldmeter used to locate and measure static charges up to $\pm$19.99 kV . While the FMX-002 has been largely superseded by the
models, its core operational procedures remain consistent with these later versions. Quick Setup & Operation Guide
: For accurate results, especially during ion balance testing, connect the grounding lead to the side of the meter and attach the other end to a known earth ground. : Press the button. A single beep indicates the device is ready.
: Point the sensor at an uncharged area (away from people or equipment) and press the button until the display reads Measurement Distance The standard measuring distance is 1 inch (25mm)
Slowly bring the meter toward the surface until the two LED light beams converge into a single concentric circle on the target. Reading the Display Numerical Value : Shows the absolute voltage. : Typically indicates a positive charge and indicates a negative charge. Hold Function : Press the
button to freeze a reading on the screen for later inspection. Core Specifications Measuring Range 0 to $\pm$1.49 kV (Low); up to $\pm$19.99 kV (High) Distance Guide Dual LED focusing lights for 25mm ($\pm$1mm) accuracy Ion Balance Up to $\pm$200V when using the detachable ion balance plate Auto Power-Off
Automatically shuts down after ~5 minutes of inactivity to save battery Ion Balance Measurement
To test ionizers, attach the metal ion balance plate to the sensor end of the FMX-002 until it clicks. Ensure the case is grounded. Press the
button to switch modes. Zero the meter in an uncharged area before holding it in the airflow of the ionizer at a distance of approximately Simco Electrostatic Field meter FMX-004 - Sumitron simco fmx002 manual full
The Simco FMX-002 is a portable, non-contact electrostatic fieldmeter used to measure static charges. It is commonly used in industrial and laboratory environments to locate static electricity on surfaces and assess ionizer efficiency. 🛠️ Key Specifications
Measurement Range: 0 to ±1.49 kV (Low range) and ±1.0 kV to ±20.0 kV (High range). Accuracy: ±10% within the standard measuring distance.
Measuring Distance: Calibrated for exactly 25 mm (1 inch) from the target. Power: Standard 9V DC battery (approx. 30 hours of life).
Housing: Conductive resin (ABS) with a grounding snap for accurate readings. 📖 Operating Instructions 1. Powering On & Zeroing
Turn On: Press the POWER button. You will hear a single beep.
Zero Adjustment: Point the sensor toward an uncharged area (or a grounded metal surface) and press the ZERO button. The display should read 0.00.
Note: Zeroing won't work if the reading is already high (>50V) or if "HOLD" is active. 2. Taking a Measurement
Distance Guide: Aim the meter at the surface. Two LED beams will form concentric circles.
Alignment: When the circles overlap perfectly, you are at the correct 25 mm distance.
Reading: The digital display and color-coded bar graph (Red for positive, Blue for negative) will show the charge. 3. Hold and Auto-Off SIMCO FMX-003 Electrostatic Fieldmeter Instruction Manual
The Simco FMX-002 is a compact, battery-powered electrostatic fieldmeter designed for measuring surface voltages up to ±19.99 kV and ionizer balance. It utilizes a 25 mm LED distance measurement system for accuracy, featuring a grounding snap, data hold function, and automatic power-off, according to SIMCO Japan and related technical documentation. The device is user-calibrated through a zeroing function and can be used with a supplied metal plate for ion balance measurements. SIMCO FMX-003 Electrostatic Fieldmeter Instruction Manual
Simco-Ion FMX-002 Go to product viewer dialog for this item.
(often succeeded by the FMX-003 and FMX-004) is a handheld electrostatic fieldmeter used to measure static charges in industrial environments. It uses an oscillating voltage sensor to detect the strength and polarity of surface charges. 📋 Technical Specifications Measurement Range: Up to (20,000V). Measuring Distance: Exactly 1 inch ( ), guided by two integrated LED ring lights. Power Source: 9V Manganese battery (typically 6F22).
Indicator: Analog/Digital LCD display with battery capacity and bar graph. ⚙️ Operating Instructions Follow these steps for accurate static measurement:
Grounding: Ensure the unit is grounded by connecting the provided ground wire to a known Earth point.
Power On: Press the red POWER button once. The unit will beep and the LCD will activate. The manual dedicates an entire page to zero adjustment
Zeroing: Point the sensor toward an uncharged area (away from the target). Press the gray ZERO button once or twice until the display reads
Measurement: Move the sensor toward the target surface. Align the two LED guide beams until they merge into a single concentrated circle on the surface.
Hold Function: Press the HOLD button to freeze a reading on the screen for easy recording. Polarity: A negative sign ( −negative
) indicates a negative charge; no sign indicates a positive charge. ⚠️ Maintenance & Safety
Avoid Contaminants: Do not use in areas with water, oil, or conductive solvents to prevent insulation failure.
Cleaning: Gently wipe the sensor area with a cloth lightly moistened with alcohol if it becomes dusty.
Battery Care: Replace the battery when the low-capacity indicator appears. Standard battery life is approximately 30 hours.
No Disassembly: Do not attempt to open or modify the unit, as this can damage sensitive internal sensors. 🛠️ Troubleshooting Common Issues
Inaccurate Readings: Usually caused by a lack of proper grounding or incorrect measuring distance.
"LO BATT" Display: Unit will not provide reliable data; replace the 9V battery immediately.
Reading Won't Zero: Ensure you are not pointing the sensor at a charged object or your own body while zeroing.
For detailed calibration or professional repair, contact authorized service providers like Micro Precision or refer to official Simco-Ion documentation. FMX-004 - Simco-Ion
Simco FMX-002 is a portable, battery-operated electrostatic fieldmeter used for measuring static charge potentials up to
. It is designed for precise, "point-and-shoot" measurements in industrial environments to locate and quantify static charges. Core Specifications Measurement Range High Range plus or minus 1.0 Ion Balance (requires attaching a metal balance plate). of reading. Measurement Distance
), precisely guided by two LED "ring lights" that must overlap on the target surface. Response Time : Less than with a display renewal rate of Construction
: Conductive resin (ABS) housing to facilitate proper grounding during use. Display and Interface Digital Display -digit auto-ranging numerical value. Visual Indicators Do not skip this step
: Red bars for positive polarity; Blue bars for negative polarity. : Indicates the reading is currently frozen. -stage capacity indicator. : Appears if the internal sensor is damaged. Operational Controls POWER Button
: Press briefly to turn on. For continuous operation (disabling the -minute auto-off), hold the button for more than until three beeps sound. ZERO Button
: Used to calibrate the meter to zero in an uncharged area before starting measurements. HOLD Button
: Freezes the current reading and bar graph, allowing the user to move the meter to a more readable position in tight spaces. MODE/IB Button
: Switches between electrostatic field measurement and Ion Balance measurement mode. Desco Industries Safety and Maintenance
: The device must be grounded using the supplied lead for accurate measurements, especially when testing ion balance. Environment : Operate in environments between relative humidity (non-condensing).
: Continuous beeping indicates an "Over Range" condition; the measurement should be stopped immediately to avoid damaging the sensor. : Ensure no foreign substances touch the internal sensor. Desco Industries For additional support or to purchase the SIMCO FMX-002 Electrostatic Fieldmeter , you can find it at retailers like Rescience Inc or more detail on how to perform the Ion Balance SIMCO Japan - FMX002 Fieldmeter
The full manual typically addresses these user questions:
Q: My FMX-002 shows "1" or "OL". Is it broken?
Q: How often should I calibrate the FMX-002?
Q: Why does my reading change when I move the unit slightly?
Q: Can I use this on a moving web or conveyor?
In the world of electrostatic field meters, few devices have achieved the legendary status of the SIMCO FMX-002. This handheld, non-contact electrostatic fieldmeter is the gold standard for professionals in the electronics manufacturing, printing, plastics, and cleanroom industries. Whether you are an ESD (Electrostatic Discharge) coordinator, a quality assurance technician, or a field service engineer, the FMX-002 is your first line of defense against static-related failures.
However, owning this sophisticated instrument is only half the battle. To unlock its full potential—accurate readings, proper calibration, and safe operation—you need the SIMCO FMX-002 manual full version. Many users lose the original paper manual or rely on fragmented online summaries. This article serves as a comprehensive resource. We will guide you on where to find the complete PDF manual, break down every button and function, provide troubleshooting steps, and explain how to interpret your measurements.
If you have been searching for the simco fmx002 manual full guide, you have come to the right place. Let’s dive deep.