English
Dollars
The error code ("A deployment or update operation is already in progress") is a Dell Lifecycle Controller message typically encountered during iDRAC or system firmware updates.
It indicates that the system's update engine is currently busy or locked by a previous task Immediate Solutions Wait for Completion
: Initial firmware packages can take over 5 minutes to download, and full updates may take much longer depending on network speed. Some users report stuck updates eventually completing after several hours. Reset the iDRAC
: If the operation is genuinely stuck, you can reset the iDRAC to clear the active update job.
This can be done via the iDRAC web interface or by holding the "i" button on the physical server for 16 seconds. Perform a Cold Boot
: This error often occurs because a RAM drive created for a previous upgrade was not cleared. Shut down the server, unplug the power cables for 10 seconds, and restart to clear the drive. Server Fault Troubleshooting Stuck Jobs Clear the Job Queue
: Use RACADM commands to forcibly clear the job queue if the UI is unresponsive. Check for Ghost Processes
: This message sometimes appears even when no operation is active if the Lifecycle Controller was not closed properly. Alternative Update Methods
: If updating via the Lifecycle Controller continues to fail, try updating directly through the iDRAC web interface by uploading the Windows 64-bit firmware file. Best Practices for Firmware Updates Sequential Updates
: For older systems, avoid skipping too many versions at once; perform updates in smaller "steps". Avoid High CPU Loads
: Do not perform firmware updates when the CPU is under heavy utilization, as it may impact cooling and stability. Use the Right File : Ensure you are using the correct
image rather than just the self-extracting executable in some interface modes. RACADM commands to clear the job queue or instructions for a physical power drain iDRAC10 Version 1.20.25.00 Release Notes - Dell
The error code indicates that a firmware deployment or update operation is already running in the Integrated Dell Remote Access Controller (iDRAC)
. This often occurs when the Lifecycle Controller (LCC) is in use or a previous update job is stuck in the queue. Key Causes Stuck Job Queue
: A previous update failed during file transfer or timed out, leaving a "lockfile" that prevents new jobs. Active LCC The error code ("A deployment or update operation
: The LCC may be performing background tasks, even if no visible update is active. Persistent RAM Drive
: The iDRAC firmware installer may have left a RAM drive on the host OS from a prior upgrade that needs clearing. Best Practices to Resolve SUP0108
If waiting for the current operation to finish does not work, use these methods to clear the error: Reset the iDRAC
: This is the most common workaround to clear stuck states and lockfiles. You can perform a reset through the iDRAC Web Interface or via the physical "i" button on the server. Force Clear the Job Queue
: Use the RACADM CLI to delete pending jobs that may be blocking the update: racadm jobqueue delete -i JID_CLEARALL_FORCE Perform a "Cold Boot"
: If a stuck RAM drive is the culprit, a full power cycle (cold boot) of the system will clear it. Update Firmware
: Ensure your iDRAC is running the latest version, as Dell has released fixes (e.g., version 7.20.10.50) specifically to address job-start failures. RACADM commands for your server generation to clear the queue? iDRAC 9 Firmware Upgrade issue - Server Fault
The error code is a common event message found in Dell PowerEdge servers
, specifically within the Integrated Dell Remote Access Controller (
) and Lifecycle Controller (LC). It indicates that "A deployment or update operation is already in progress" and prevents you from starting new firmware updates or mounting drivers. Core Cause Analysis
This error typically occurs when the system detects a "lockfile" or active process that hasn't cleared, even if no operation appears active in the UI. Stuck RAM Drive
: The iDRAC installer sometimes places a RAM drive on the host OS to extract firmware. If this isn't cleared after a previous run, subsequent updates are blocked. Failed Previous Jobs
: A job that failed during file transfer can leave the system in a "Downloading" or "Timeout" state, blocking the queue. Lifecycle Controller in Use
: The error can trigger if the Lifecycle Controller is active for another task, such as hardware inventory or a background driver pack update. Server Fault Step-by-Step Resolution Guide 1. Immediate Workaround: Reset iDRAC Causes of the SUP0108 Error The SUP0108 error
The fastest way to clear stuck locks and "New" job states is to perform a soft reset of the iDRAC. This does not affect the host operating system's availability. Via Web UI : Log in to iDRAC, go to the Maintenance tab, select Diagnostics , and click Reset iDRAC Via CLI (RACADM) : Run the command racadm racreset 2. Clear the Job Queue
If the reset doesn't work, there may be a persistent job blocking the queue. iDRAC10 Version 1.20.25.00 Release Notes - Dell
Resolving the "SUP0108: A deployment or update operation is already in progress" Error: Best Practices and Solutions
The "SUP0108: A deployment or update operation is already in progress" error is a common issue that system administrators and IT professionals encounter when working with Microsoft System Center Configuration Manager (SCCM) or other deployment tools. This error occurs when a deployment or update operation is attempted while another operation is still in progress, causing conflicts and preventing the new operation from completing successfully.
In this article, we will explore the causes of the SUP0108 error, discuss best practices for avoiding it, and provide step-by-step solutions for resolving the issue.
Understanding the SUP0108 Error
The SUP0108 error typically occurs when there are multiple deployment or update operations running concurrently, causing a conflict. This conflict prevents the new operation from completing, resulting in the error message:
"A deployment or update operation is already in progress. Please wait until the current operation is complete and then try again."
The SUP0108 error can occur in various scenarios, including:
Causes of the SUP0108 Error
The SUP0108 error can be attributed to several causes, including:
Best Practices for Avoiding the SUP0108 Error
To avoid the SUP0108 error, follow these best practices:
Solutions for Resolving the SUP0108 Error Best Practices for Avoiding the SUP0108 Error To
If you encounter the SUP0108 error, follow these step-by-step solutions:
Solution 1: Wait for the Current Operation to Complete
Solution 2: Cancel the Current Operation
Solution 3: Use the SCCM Console to Resolve the Issue
Solution 4: Use PowerShell to Resolve the Issue
Conclusion
The SUP0108 error can be a frustrating issue for system administrators and IT professionals working with SCCM or other deployment tools. By understanding the causes of the error, following best practices for avoiding it, and using the solutions provided in this article, you can resolve the issue efficiently and effectively.
Here’s a clear, ready-to-use piece (e.g., for a knowledge base, error message, or troubleshooting guide) based on your query:
Error: “SUP0108 — A deployment or update operation is already in progress”
Meaning:
You tried to start a new deployment or update, but the system is already running one. Concurrent operations are not allowed.
Best course of action:
Best practice to prevent this:
Tip: If you’re certain no operation is running, manually clear the stale lock from the admin console (
/admin/deployments/resetor equivalent).
After upgrading to a new version of Configuration Manager (e.g., 2207 to 2303), the WSUS configuration might be reset, or a background migration task might still be running.
